Easy to use and foolproof.

Perform tests like a pro!

Analyze exact battery characteristics.

Match cells or pick the best pack.

Check for battery aging.

Cycle and condition batteries.

Test at up to 150 watts or 40 Amps.

• Plug and Play high speed USB interface, with easy to use and intuitive Windows software supplied on CD ROM.
• Scientifically analyzes battery performance with a true constant current battery capacity test that is graphically displayed.
• Perform tests quickly at real world load conditions, up to 150 watts or 40 amps!
• High voltage testing at up to 48 volts; the equivalent of 1 to 38 NiCad or NiMh cells.
• Save, display and print battery test graphs and battery labels.
• Measures and displays voltage, current, amp-hrs, watts and temperature*.
• Easy overlay comparisons of multiple graphs may be displayed saved and recalled.
• Test any type of battery: NiCad, NiMH, Lead Acid, Li Ion, Li Poly, Alkaline, Carbon Zinc, Mercury etc; from coin cell to automotive or larger.
• Accurate measurement with up to 12 bit resolution. Auto selection of two current and three voltage ranges.
• Each CBA is individually, digitally calibrated, against NBS traceable instruments.
• On board C8051 based USB Micro controller.
• Superior, software and electronically regulated, constant current testing using a solid state FET fan cooled electronic load.
• Automatic test shut off at a safe pre-determined minimum battery voltage. Default shut off voltage may be user overridden.
• Automatic test shut off at a for a pre-determined maximum battery temperature. (Requires optional temperature probe)
• Fail safe: software and/or hardware protection of temperature, current, power and reverse polarity.
• Supplied with USB cable and high grade 13 gauge flexible Powerpole battery test cable. Optional adapters available for most batteries.
• Optional external temperature sensor provides measurement of battery temperature for complete testing.
• Maximum test rate: 150 watts or 40 amps, whichever is higher.
• Discharge test current user selectable from 0 to 40 Amps.

The CBA is capable of higher test rates than other testers: up to 40 amps or 150 watts, whichever is higher. It not only tests the total amount of energy stored in a battery (capacity in amp-hrs), but it graphically displays and charts voltage versus amp-hours.

Unlike a resistor load it has a constant current load that is controlled both with software and electronically.

Graphs may be displayed, saved and printed. Multiple graphs of the same battery, or multiple batteries, may be compared or overlaid, a very useful feature. Battery tests may be printed on a color or black and white printer. You may also print convenient test labels to placed directly on your batteries to remember the last time they were tested and how they performed.

A CBA will measure the temperature of a battery under test using the optional external temperature probe. The temperature probe will provide automatic over-temperature shutoff a preset temperature limit.

The CBA is ruggedly built and it is supplied with high grade wire with Powerpole battery connectors. Other connectors may be installed our you may use our adaptors or make adaptors to the Powerpoles. A CBA is compact and has a high performance cooling system with a quiet fan. LED indicators show test status from across a room.

The CBA uses an 8051 based micro controller. Each CBA is individually calibrated to high accuracy. The electronic load uses a pulse width modulation system to control a power MOS FET with electronic and software current regulation. The on-board micro controller provides the plug-and-play USB interface to the computer.

Maximum continuous discharge rate: 100 watts

Maximum limited term discharge rate with < 3500 ma-hour battery: 125 watts

Maximum limited term discharge rate with < 1000 ma-hour battery: 150 watts

0-3 amp accuracy: typically better than + - 10 ma (12 bit, NEW! CBA II)

3-40 amp accuracy: typically better than + - 45 ma (10 bit resolution)

0-5 volt accuracy: typically better than + - .005 volts (10 bit resolution)

5-10 volt accuracy: typically better than + - .01 volts (10 bit resolution)

10-50 volt accuracy: typically better than + - .05 volts (10 bit resolution)

Maximum operating voltage: 48 Volts (48 Volt Lead Acid not supported)

Maximum discharge rate: 40 amps (3.75 Volts at test start)(Battery dependant)

Minimum Voltage for a 40 amp discharge: 2 volts at completion of test (Battery dependant)

Minimum discharge rate: 0.0 Amps

Residual current drain, battery connected while not in use: < .003 amps @ 12 volts

User selected battery cell chemistry, number of cells and test current, with automatic graph setup and scaling.

High performance C8051 based micro controller with built in USB interface and 10 bit A/D conversion.

USB powered; the CBA does not use the battery being tested to run the CBA or the fan.

Software recommends safe tests based on user supplied battery information.

Supplied with: USB cable, Powerpole battery connectors and Windows compatible software CD with full documentation.

System ready and Test in progress LED indicators, viewable from across a room.

Automatic voltage shut off at end of test using a software recommended or user selected safe discharge voltage.

Automatic over-temperature shut off at end of test at using a software recommended or user selected maximum temperature.

Optional external magnetic temperature sensor required for temperature measurement and/or battery auto over-temp shutoff.

Internal automatic self protection of over temperature.

Graph printing on any standard color or B&W printer.

Battery test label printing on standard 05160 stick-on labels.

Dimensions: 3.5" H x 2.8" W x 3.6" D.

Weight: 16 oz.